How To Make A Bowl Out Of Water Bottle

Download Commodity

Download Article

Is your bong currently out of commission? Not to worry; with just an empty h2o bottle and a little aluminum foil, y'all'll exist back in business. We've put together an easy, footstep-by-step guide to help you make a water bottle bong of your very own. Interested in making a water pipe? We've got you covered there, too—coil downwardly the second section for a handy tutorial.

1
Obtain a canteen. You lot will want to apply a bottle that is merely the right size for bong-making purposes. A standard 16.ix ounce plastic water bottle should do the trick.
- Water bottles are amend than soda bottles because they won't leave any sticky residual.
- You can remove the label from the bottle, if you desire.
- Y'all don't take to leave any water in the canteen. However, if you lot want the bong to stand upright, you lot can get out some in to weigh it down.
- This is not a traditional bong, because it does not forcefulness the smoke through the h2o; still, it can be made rapidly and easily.
2

Remove the lid. Set up information technology aside. You will not need it.

Advertisement
iii
Tear off a small piece of aluminum foil. This piece will serve as the bowl. It should be approximately 2.v inches by 2.5 inches (5cm by 5 cm). You should apply thick or "heavy duty" aluminum foil for best results.
- If you lot but accept lightweight aluminum foil, fold information technology over to make it thicker before forming a 2.five inch by ii.five inch foursquare.
- The piece of aluminum foil should be large enough to comprehend the mouth of the bottle and fold over the edges. Look at your canteen; if 2.5 inches past 2.v inches doesn't seem large enough, tear off a larger piece of aluminum foil.
4
Apply the foil. Wrap the edges of the aluminum foil around the meridian of the open h2o canteen. Press your thumb downwards to extend the aluminum foil into the center of the opening. It should class a depressed basin shape in the peak of the h2o bottle.
- Brand the bowl depression large enough to contain your herb, but don't push button downward and then hard that yous tear the aluminum foil.
- Aluminum tin can be toxic if used improperly, such as by heating, inhaling, or ingesting it.^[1] ^[2]
5
Poke holes in the aluminum foil basin. 5 or six holes are probably adequate. Use a needle, straight pin, toothpick, or other slender object to poke the holes.
- Make sure that the holes are far enough autonomously that they do not break the bowl.
- Be careful not to poke holes so large that they suspension the bowl.
6
Dial a pigsty in the side of the bottle. Poke some other pigsty into the outside portion of the water bottle, just above where the characterization stops. This is where yous volition demand to place your oral cavity.
- Don't effort to make the hole too big. Gently poke a hole with your needle or directly pin, and so jerk information technology around a bit to make the hole a little bigger.
7
Brand the side pigsty bigger with a pair of scissors. Make it approximately 1 inch (2.5cm) in bore to first. Be conscientious not to rip the bottle; press down on the hole to indent the plastic slightly, then gently overstate the pigsty.
- Start by making the hole a niggling on the small side. You tin always enlarge it later if you need to, but you tin can't make it smaller.
eight
Pack the bowl. Just identify some of your favorite herb in the aluminum foil bowl. Don't overdo it; you tin always add more later, but you don't want information technology spilling over the sides.
- If pieces of your herb fall through the basin, and then the holes y'all punched are besides large. Take the aluminum foil off and endeavour again, this time making smaller holes.
ix

Smoke. Encompass the hole on the side with your oral cavity. Lite the basin and let the smoke fill the water bottle bong.
10

Inhale gently. As you light the bowl and smoke fills the water bottle, set downward the lighter and gently inhale the smoke in the bottle.

Advertizement

1
Obtain a canteen. ^[3] Some people like to use a 2-liter bottle, but a standard xvi.9 ounce water bottle can also work just fine.
- Remove the lid from the bottle and discard it.
2

Take apart a plastic pen. ^[4] Yous will need the pen shaft to work as a fume shaft. Any plastic pen that can be taken apart to leave a hollow cylinder volition work.
3

Cut a hole in the side of the canteen. ^[5] Using pair of scissors or another tool, gently poke a pocket-size hole (just big enough to insert the pen shaft) in the side of the canteen, approximately i/3 the altitude from the lesser. Your pen shaft will extend at an bending into the water.
4
Insert the pen shaft into the pigsty. ^{[half dozen]} Examination the size of the hole by inserting the pen in the hole at a downward bending. If the hole is too big, information technology volition exist difficult to become a tight seal.
- If it turns out that your hole is too big, y'all can notwithstanding salvage the bong. But identify pieces of tape where the pen shaft meets the bottle to brand a tighter seal.
5

Pierce a carb into the bottle. On the contrary side of the bottle, brand another small hole (about the size of a pencil eraser).^[7] This will exist used as the carb when you are smoking.
half-dozen
Attach a bowl. Affix a metal socket to the outside end of the pen shaft. Use another few layers of duct tape to brand a seal. The socket is your basin.
- You tin use whatsoever sort of metal socket that is the right size. Look effectually your house for a suitable object. If y'all tin't find anything, visit a hardware store, where you'll find lots of possibilities.
7

Make full the bong with water. Pour water from the top of the bottle into the bottom of the bong. Fill it approximately i/5 total.
8

Pack the basin. Simply identify some of your favorite herb in the metallic socket bowl. Don't overdo it; you lot tin always add together more later, just you don't want it spilling over the sides.
9

Position the bong. Place your oral cavity at the tiptop of the bottle, where the lid was. Tip the bell so that the bowl is facing away from your torso.
10

Light the bowl. Using a lighter, ignite your herb and begin to suck in slowly to force the smoke through the water. Make certain to place a finger over the carb hole while doing this.
11

Smoke. Set the lighter down when the canteen is filled with fume. Remove your finger from the carb pigsty. Suck the smoke in securely through the top of the bottle.

Advertizing

Ask a Question

200 characters left

Include your electronic mail address to get a message when this question is answered.

Submit

Advertizement

About This Article

Commodity Summary 10

To make a water bottle bong, find an empty plastic water bottle and accept the cap off. Then, cover the mouthpiece with a two.5 by two.5 inch piece of aluminum foil. Printing downward on the aluminum foil with your thumb so information technology's bowl-shaped and and so poke 6 holes in the foil with a toothpick or hairpin. To terminate the bong, utilize a pair of scissors to make a 1 inch hole in the side of the bottle, right above where the label is. For help using your new water bottle bong, scroll downwards!

Did this summary help you?

Thanks to all authors for creating a page that has been read ii,554,062 times.