How To Connect Ground Wire To Water Pipe

how to run a ground wire to an electrical panel

When talking about electrical safety, one of the main topics that should exist discussed is the existence of basis wires.

Although ground wires are not required for an electric instrument to work properly, attaching ground wire to electrical box is a norm for electricians because information technology provides an boosted safety feature that can salvage your life in accidents.

Normally, ground wires do not bear current. Current volition only pass through ground wires when there is an excessive amount of information technology or the original path has been damaged.

If yous're wondering how to run a footing wire to an electric panel, keep reading!

Tabular array of Contents

Tool For Connecting Your Basis Wire to An Electrical Panel
Steps on How to Connect Ground Wire to Electrical Panel
- Step 1. Basis bar or rod Installation
- Step two. Attach your ground wire to the footing rod
- Step 3. Go along the breakers off
- Pace iv. Remove panel encompass
- Step 5. Pick a proper knock-out hole
- Step 6. Locate neutral bar or grounding bar
- Step 7. Connect the ground wire to the bar or rod
- Pace 8. Finish up
Importance of Grounding
Conclusion

Tool For Connecting Your Ground Wire to An Electrical Panel

attaching-ground-wire-to-electrical-box

Ground bar or rod

Regarding the materials to be used in ground rods, it is highly suggested that you apply galvanized steel, stainless steel, or copper-bonded steel. Among these three, galvanized steel is the cheapest and frequently preferred by experienced electricians.

Mallet
Screwdriver
Ground wire (usually a 6-gauge copper wire or bigger)
Clamp
Multimeter
Protective equipment

Steps on How to Connect Basis Wire to Electrical Panel

Step 1. Ground bar or rod Installation

connect-the-ground-wire

The first step in running a footing wire to your electrical panel is to starting time know where you lot want the excess electric current to flow. Since you cannot just leave your ground wire hanging or attached to the ground, you lot need a ground bar or basis rod where your ground wire will be continued.

It is suggested that yous bury the rod upward to eight feet below ground and leave 3 to 4 inches above the ground where your ground wire will exist attached.

If all conditions are met, you may showtime driving your ground rod to the soil outside your firm with a mallet. Brand certain a passerby won't stumble on the above-basis rod where your wire is beingness connected.

Step 2. Attach your ground wire to the ground rod

Connect the ground wire to the rod using a clamp. Secure the connection.

Footstep 3. Continue the breakers off

ground-wire-go-in-electric-panel

Before doing electrical installations, it is imperative that you should ever check your breakers and proceed them off, unless you lot are virtually to test your work.

Turning off your breakers will let you piece of work safely and avoid electrical damage or even electrocution.

Step 4. Remove console cover

Virtually electric panel covers or faceplates are intact by screws. To remove the panel cover, get a proper screwdriver to be used, either a flathead screwdriver or crosshead-screwdriver, depending on what screw heads were used.

Footstep 5. Pick a proper knock-out hole

The knock-out pigsty is a detachable part on the console'due south surface where wires that should be inserted within the panel are threaded.

Know the location of the proper knock-out hole to exist used, depending on where you lot put your ground bar. Pick a hole where the ground bar or footing rod is nearest.

Pace 6. Locate neutral bar or grounding bar

Most electrical panels have a grounding bar built inside where ground wires should exist attached. Withal, there are some electrical panels where at that place are no built-in basis confined. If that is the instance, your ground wire should exist attached to the neutral bar.

Step 7. Connect the basis wire to the bar or rod

connect-ground-wire-to-electrical-panel

Using a #half dozen gauge copper wire, first adhere 1 end of the wire in the basis bar or neutral bar inside the electrical panel. Make certain y'all insert the wire through a knockout hole near the basis rod located outside the house to minimize the unnecessary angle of the grounding wire.

Advisedly fix the footing wire until it reaches the ground rod located exterior the house. You may use wire ties if necessary to avoid wire tangling.

On the other end of the wire, make sure that the end is completely fastened to the ground bar in club to completely eradicate the possible loosening of the ground wire.

Besides, the wire should not hinder any pathways. Make sure also that the footing wire is gratis from thorns or damages.

Step eight. Finish up

Switch the breakers on so start testing. Do not forget to use personal protective equipment when dealing with electric testing.

You may use a multimeter to test for resistance. It should be shut to Zero "0" to say that grounding is effective.

If everything went perfect, close the faceplate and administer the screws into their original places.

Importance of Grounding

Grounding is the process where you adhere a ground wire into the grounding bar to preclude excess electric current from flowing through undesired locations.

Nosotros can all concord that the main purpose of grounding your electric panels, even appliances, too, is to prevent electrocution when the normal path of current is damaged or deemed unserviceable.

Having your electric panel grounded, y'all and so keep all your outlets grounded since all outlets in your business firm must be continued through an electric panel, which serves every bit the chief energy source.

Inquiry says more than one death per solar day happens due to electrocution in the United states of america alone. Having an actress layer of condom features in your house is the best matter to do to eliminate or mitigate risks that tin can put your life at stake.

Conclusion

After reading this commodity, yous should now know how to run a ground wire to an electrical panel.

Whenever working with electronics and electrical wiring, prophylactic should be our utmost priority. Safety precautions should not stop after completing the job because at that place are other chance factors that may lead to serious injury or even death.

Attaching a ground wire to an electrical box mitigates the risk of injuries or even electrocution. Share this article if you feel that others might want to know about this besides.

I am Edwin Jones, in charge of designing content for Galvinpower. I aspire to use my experiences in marketing to create reliable and necessary information to help our readers. It has been fun to work with Andrew and utilise his incredible knowledge to our content.